How to open a non-mounted cherry MX switch?

User avatar
Mrinterface

06 Mar 2012, 11:18

I'm working on my switch try boards and I know how to open a cherry MX switch which is mounted, but how do I properly open one that's not mounted?
The best thing technique I have a.t.m. is to hold it with a pincer and wriggle my way in with a tiny screwdriver but that is very very tedious. I already lost a spring that way since they tend to 'burst' open with this technique.
With the amount of work needed to open those non-mounted switches, I might as well start to desolder/solder them.

Any tips on techniques?

I posted this in Workshop since I guess the answers can benefit others as well.

Regards.

User avatar
Ascaii
The Beard

06 Mar 2012, 11:55

I have a small square piece of plastic foam that I stick the switch on, then I hold the switch between thumb and pointing finger, holding down the steam. click open with screwdrivers.

User avatar
Mrinterface

06 Mar 2012, 11:57

Ascaii wrote:I have a small square piece of plastic foam that I stick the switch on, then I hold the switch between thumb and pointing finger, holding down the steam. click open with screwdrivers.
Thanx. Gonna try that.

User avatar
Icarium

06 Mar 2012, 12:00

I'm not sure I understand the problem. I just use two toothpicks to open each side a little and then pull them apart. I've never had one burst open but maybe I'm just working a lot slower than you. :)

User avatar
Mrinterface

06 Mar 2012, 12:16

Icarium wrote:I'm not sure I understand the problem. I just use two toothpicks to open each side a little and then pull them apart. I've never had one burst open but maybe I'm just working a lot slower than you. :)
Two toothpicks at the same time for every side? Gonna try that as well....

EDIT : the problem is that I don't want to damage the contact wires when opening them so I can't just push them on a table and open them since the wires will get damaged.

User avatar
harrison

06 Mar 2012, 20:21

i'll see if i can take a quick vid tonight... i just got done with ~300 of them after desoldering two keyboards and breaking down the switches.

i hold the switch in my left hand (i'm right handed) between my index and thumb, with the stem pointed towards the palm of my hand. i use a small flat head screwdriver to press and twist on one of the top case legs until the spring tension pops the leg over the notch. i then use my fingernail in the separation between the housing, and use the screwdriver on the second leg. at this point, the top case is half off. i rotate the switch, and hold it using my middle finger and thumb, with my index just touching the stem. i then release both of the other case legs.

my index finger holds a small amount of tension on the stem, so that the stem/spring don't go flying.

alternatively, when you flip the switch over, you can hold it between your index and thumb, but on the sides of the housing so that the pressure from your fingers don't allow the housing to separate more than a few mm when the two legs are released.

User avatar
Mrinterface

07 Mar 2012, 16:52

Thanx harrison, now I have four techniques I can try....

User avatar
hasu

17 Mar 2012, 06:20

I'm not sure this solves your problem though.
I made limmy's cherry opener the other day and I found it is easier than precision driver.
Image
http://www.kbdmania.net/xe/index.php?mi ... rl=3520312

User avatar
Maarten

17 Mar 2012, 08:59

Oh that looks alot like the tool i use, only mine is longer so i can press the ends of the 'handles' up against each other without over bending (and possibly breaking) the plastic housing top.

symphonic

28 Mar 2012, 00:49

Oh man I started typing a reply about using binder clips, and then saw the above post! I guess that no idea is a truly new idea.

I don't put my ends inside though, but rather lever up the plastic by rocking back from the outside of the switch case.

User avatar
Julle

31 Mar 2012, 09:06

I don't if my method is any better than the ones mentioned here before, but this is what I like to do: I take two top halves of a Cherry MX switch housing and super/hot glue them upside down on a piece of board. I attach them to the board (a little less than switch width apart) so that when you lower an intact switch between them, the clips pointing upward will enter between the clips of the intact switch, opening all four sides at the same time.

This method opens the switches very effortlessly and is very gentle to the switch housing as well.

Tarkoon

31 Mar 2012, 09:15

Could you make a photo of this construction?

User avatar
Julle

31 Mar 2012, 09:44

It's not pretty, but it darn well works! My arrows are a bit misleading, the 8 millimetres is the distance between the inner surfaces of the switch clips.

With this you can only open plate mounted switches:
Image

But if you want to open both plate and PCB mounted switches, you have to do a little surgery:
Image

Image

Image


Works like a charm! the top half of the switch won't be flying anywhere, since it's being held by the clips on my opening jig.
Image

User avatar
Julle

31 Mar 2012, 10:17

One thing I forgot to mention: it's a good thing to reinforce the clips on the jig with some hot glue as well so they won't bend in use.

User avatar
Mrinterface

31 Mar 2012, 10:19

Great stuff there Julle..... How did you get to this idea? Trial and error I guess :-)

User avatar
Maarten

03 Apr 2012, 17:16

WOHOO!!! An excuse to try out my new close-up video rig! unfortunatly my PC didnt wanna eat the camera drivers so its still pretty crappy quality-wise but at least the lighting and stuff is ok;
As you can see i did all the dis-assembly with GLOVES for two quite simple reasons; First is that if i can do this kind of fiddly thing with gloves then everybody should be able to do this job... And second, well, my hands are a crappy bloody mess and i dont wanna ruin anyones appetite here :lol: ! Hope you guys like!

User avatar
Mrinterface

03 Apr 2012, 17:41

Great vid!

Your hands are a bloody mess? Do you have a cat with a temper?

Where did you get those two pincers from? Self-made?

User avatar
Maarten

03 Apr 2012, 17:57

Mrinterface wrote:Great vid!

Your hands are a bloody mess? Do you have a cat with a temper?

Where did you get those two pincers from? Self-made?
Bloody mess.. well yeah, cat did help that much but main causes are working on the car.... i use gloves till i have to some something under an absurd angle or tight spot i have to work on and when i go on with the regular work i kinda forget to put em back on again.... And ive also been working in the garden alot last couple of days with the basic same problem ;) Also cut my finger a little while ago quite deep with an x-acto blade, wound wouldn't close so i had to tie my finger with rubber bands and spuer-glue it all back together. Works like a charm just isnt very pretty.

And yeah, 'tools' were made from good ol regular paperclips bent into the rouigh shape you see in the vid and filed to a sharp-ish point. Here's pics cuz i know yall love those;

Image
Image

I also added some shrinkrap so they are a bit easier to handle and so i dont accidentally mistake em for 'regular' pieces of left over paperclip and toss em when cleaning up :lol:

User avatar
Kurk

13 May 2012, 20:58

Here's my technique: it involves a pair of modified angled tweezers (tips bent by 90°) and a small screw driver. I've tried it with two tweezers but the tweezer-screw driver combination works better.
The tools.
The tools.
opencherrytools_resized.jpg (137.07 KiB) Viewed 14093 times

User avatar
off

23 May 2012, 00:30

Hey Kurrk, did you heat it before/while twisting the tweezer ends, or just plain vanilla twisted them?
'Cause that does look like an even nicer tool than the paperbinder I was planning to sacrifice (copying someone else)..

User avatar
Kurk

23 May 2012, 10:04

off wrote:Hey Kurrk, did you heat it before/while twisting the tweezer ends, or just plain vanilla twisted them?
'Cause that does look like an even nicer tool than the paperbinder I was planning to sacrifice (copying someone else)..
I've just bent the ends using two pliers. This may only be that easy with *cheap* tweezers. The ones I used were 1 EUR for a set of four different shapes (at a local "Karwei" DIY store, or was it the "Gamma"?).

ripster

23 May 2012, 15:35

Fondue forkOdeath!
http: //geekhack.org/attachment.php?attachmentid=5054&d=1255001310
Last edited by ripster on 03 Jun 2012, 18:48, edited 1 time in total.

squarebox

03 Jun 2012, 18:35

Here's my method...
Make sure you inside of the slots.
Image

bpiphany

08 Jun 2012, 09:54

This is how I usually do it. It makes my thumb hurt after a while though, so I probably should replace my method with something better. I really like Maarten's paper clips. It would be great if they were one piece, longer, and tweezer like. Adjusting the spread squeezing them together while inserting both sides at the same time. And after that squeezing further to do the popping.

http://flickr.com/gp/67486915@N03/48q8ie sorry for the quality...

tubby

14 Jul 2012, 19:13

I made this "tool" from a tin plate =)
Image

Not sightly, but it really helps in popping off a switch, whether it's mounted or not.

maxrunner

05 Oct 2012, 17:27

Maarten wrote:WOHOO!!! An excuse to try out my new close-up video rig! unfortunatly my PC didnt wanna eat the camera drivers so its still pretty crappy quality-wise but at least the lighting and stuff is ok;
As you can see i did all the dis-assembly with GLOVES for two quite simple reasons; First is that if i can do this kind of fiddly thing with gloves then everybody should be able to do this job... And second, well, my hands are a crappy bloody mess and i dont wanna ruin anyones appetite here :lol: ! Hope you guys like!
Hi there! Where can i get two of these??That looks way easy to open the switch

User avatar
kbdfr
The Tiproman

05 Oct 2012, 17:39

maxrunner wrote:
Maarten wrote:[…]
Hi there! Where can i get two of these??That looks way easy to open the switch
Please do read first what Maarten wrote just a few posts ago on this very same page:
http://deskthority.net/workshop-f7/how- ... tml#p40927

maxrunner

05 Oct 2012, 18:15

Yep, interesting, i need to find a good tool for this.I'm going to mod my G80-3000 with other switch type. I dont really like blacks. But i do like browns and blues, any advise on wich one i might consider changing, i'm interested in testing others. People seem to like the ergo clears....i need the clears stem plus what kind of spring, a blue/brown one?

User avatar
Vierax

05 Oct 2012, 20:31

max > I have to repeat myself : I beg you to RTFM please. With the wiki and this forum you really can find easily those infos you ask.

User avatar
RC-1140

05 Oct 2012, 20:41

To be honest, you're getting really annoying. Read before you post.
All the information you're asking for can be found in the wiki. If you read the posts above, you would have known that Maarten made this tool by himself out of paperclips. Also if you read the wiki you would have known that Ergoclears are made from Clear stems with Blue/Red/Brown springs.

RTFM. Really.

Post Reply

Return to “Workshop”