FS: PS/2 or ADB to USB R3scan® converters

User avatar
Wingklip

17 May 2019, 15:31

Hi all,

I'm selling some soarer/hasu compatible converters that I had designed and improved after two years in development and production. I've finally completed the first run, so orders can be placed now!

The price is $25 USD FLAT including global untracked insured shipping.
https://docs.google.com/forms/d/1gVTN3z ... KA-Tg1juU/

Photos below. The case is a magnetic snap fit, which means you can resolder the connections and reprogram it at will. Also drop damage resistant. Screw mountable.

1KOHM resistor is already soldered for the pullup, so feel free to use long cables.
IMG_20190517_225632.jpg
IMG_20190517_225632.jpg (1.86 MiB) Viewed 674 times
IMG_20190517_225445.jpg
IMG_20190517_225445.jpg (2.11 MiB) Viewed 674 times
IMG_20190517_225250.jpg
IMG_20190517_225250.jpg (999.91 KiB) Viewed 674 times
IMG_20190517_225829.jpg
IMG_20190517_225829.jpg (2.93 MiB) Viewed 674 times
INSTRUCTIONS******
Instructions for Assembly: (or a simple case of square block in the square hole)
1. Remove any tape, wrapping, or cardboard from the package carefully, DO NOT pierce the cardboard on the flat sides. Using a pen is recommended over sharp objects such as knives
2. Seperate the case from the pro micro and port. They are mounted in a shipping configuration to satisfy the thickness limitations.
3. Plug the PS2 or ADB port into the corresponding half with the holes in the case matching, using sufficient force to ensure a snug fit. This is hereby known as the BOTTOM SHELL. Place the pro micro flat with the microUSB port face facing towards the user onto the BOTTOM SHELL. Press fit lightly into the case. ALL CONNECTORS WILL CLEAR THE CASE UNLESS PLACED IMPROPERLY OR ON THE WRONG HALF SHELL. If you fail this after reading, please reconsider your life :)
4. Make sure the wires are tucked into the center of the pro micro and then press down the TOP SHELL. Ensure there is no gap, and that all ports clear the TOP SHELL. The shell case will only be openable should sufficient pulling force be exerted upon the shells.

If the end user breaks a component during assembly they shall be responsible for the purchase of the corresponding part as per the price below (incl postage):

Pro Micro w/resistor and Pins presoldered: $10
Case w/Magnets: $10
Connector ADB/PS2: $5

All items are inclusive of shipping and in USD. Only available to the owners of a R3scan converter
Last edited by Wingklip on 19 Jun 2019, 09:42, edited 7 times in total.

Engicoder

17 May 2019, 16:02

These look nice and compact. Good job on the case. Good luck!

User avatar
Wingklip

17 May 2019, 17:56

Engicoder wrote:
17 May 2019, 16:02
These look nice and compact. Good job on the case. Good luck!
Thanks, spent hours trying to make it look perfect

User avatar
Wingklip

19 May 2019, 05:31

Price has been dropped to $25USD each for the first batch of 50 :)

User avatar
Wingklip

25 May 2019, 08:27

All paid orders have been sent out. Special thanks to all of the first four purchasers of this converter!

the_ambyguous

07 Jun 2019, 21:21

aw man, no idea if this is still available but just submitted a request for one ps2

User avatar
Wingklip

08 Jun 2019, 03:14

Still available, but you'll probably have to wait a week or so more than usual as I'm currently doing uni as well :)

User avatar
Wingklip

16 Jul 2019, 08:08

To all purchasers of my converter! Results are in, shipping may take up to 7 weeks to arrive as letters are quite unreliable, but are the only option I have to make these at this price. General time I've seen is from 1-7 weeks it seems

If you don't get it after then feel free to hit me up to discuss resends or refunds etc

Post Reply

Return to “For sale”