I have the next few days off so I'm going to get a start on trying to convert my IBM 5121 keyboard. I haven't done any research yet, but it seems like people almost always put an xwhatsit or commonsense controller in these. I might eventually go that route but I'd like to mess around with it a bit first.
Here are some photos of the keyboard.
IBM 5121 Conversion
- snacksthecat
- ✶✶✶✶
- Location: USA
- Main keyboard: SSK
- Main mouse: BenQ ZOWIE EC1-A
- DT Pro Member: 0205
- Contact:
- snacksthecat
- ✶✶✶✶
- Location: USA
- Main keyboard: SSK
- Main mouse: BenQ ZOWIE EC1-A
- DT Pro Member: 0205
- Contact:
I've got everything wired up based on the connector pinout found on kbdbabel
However, according to this I need to supply -5v to one of the pins. I'm not sure how to do that. Does anyone here know how I could power this keyboard?
I need to supply 5v, -5v, and 8.5v (I have a 9v step up regulator). I'm not opposed to purchasing something.
Thanks!
However, according to this I need to supply -5v to one of the pins. I'm not sure how to do that. Does anyone here know how I could power this keyboard?
I need to supply 5v, -5v, and 8.5v (I have a 9v step up regulator). I'm not opposed to purchasing something.
Thanks!
- snacksthecat
- ✶✶✶✶
- Location: USA
- Main keyboard: SSK
- Main mouse: BenQ ZOWIE EC1-A
- DT Pro Member: 0205
- Contact:
Bump
I don't understand electricity. Can any of the bright minds of DT help me learn? I need to power this keyboard with 5v, -5v, and 8.5v.
I don't understand electricity. Can any of the bright minds of DT help me learn? I need to power this keyboard with 5v, -5v, and 8.5v.
- Muirium
- µ
- Location: Edinburgh, Scotland
- Main keyboard: HHKB Type-S with Bluetooth by Hasu
- Main mouse: Apple Magic Mouse
- Favorite switch: Gotta Try 'Em All
- DT Pro Member: µ
GND == 0 volts. Everything else is based off that. Put a 5v source's negative end on GND and positive end on +5 and you've got yourself +5v; swap it round and you've got -5v. GND is the common.
The pinout does kind of invite powering it up and watching those Scan Bit lines. Note how there's 7 of them: reminds me of ASCII. Keyboard protocols are usually a bit more complex than that, however. I mean, if you did power it up, poked keys, and it spat out ASCII codes, it'd be 1KRO!
(And don't forget IBM had an iffy relationship with ASCII, what with EBCDIC. Hopefully that all pre-dated this board and its mysterious protocol.)
Ultimately, you're turning towards CommonSense, I'm sure! But there's no obvious harm to be done playing with IBM's original controller first, I suppose. Just don't go frying batteries or power supplies with short circuits!
The pinout does kind of invite powering it up and watching those Scan Bit lines. Note how there's 7 of them: reminds me of ASCII. Keyboard protocols are usually a bit more complex than that, however. I mean, if you did power it up, poked keys, and it spat out ASCII codes, it'd be 1KRO!
(And don't forget IBM had an iffy relationship with ASCII, what with EBCDIC. Hopefully that all pre-dated this board and its mysterious protocol.)
Ultimately, you're turning towards CommonSense, I'm sure! But there's no obvious harm to be done playing with IBM's original controller first, I suppose. Just don't go frying batteries or power supplies with short circuits!
- pansku
- Member of the Beam Spring cult
- Location: Finland
- Main keyboard: IBM 5251
- Main mouse: Mionix Castor
- Favorite switch: Beam spring
- DT Pro Member: 0197
Personally I wouldn't try reinventing the wheel. There is a converter using the original controller already.
https://github.com/MMcM/ibm-5251-kbd
https://github.com/MMcM/ibm-5251-kbd