[FS] Dactyl-Manuforms, Ergodox, Krytox

User avatar
Loligagger

18 Apr 2018, 03:33

All prices are in USD (including paypal fees), not including shipping.

Keep in mind shipment is from Canada. Feel free to send me offers.


For sale:

-Dactyl-Manuform, 5x7 layout with drop holy pandas. The pandas have been lubed with tribosys 3203. Keycaps are blank PBT DSA. Case is printed with prusament gentleman's grey. Under certain light it has a beautiful green sheen to it. Normally its color is a blue/grey. Here is an internal shot. Comes with a braided TRRS cable. If you don't need the keycaps or TRRS cable just subtract $25 or $2.50 respectively from the asking price.
Asking $344
IMG_20210406_190343.jpg
IMG_20210406_190343.jpg (840.09 KiB) Viewed 349 times

-Dactyl-Manuform, 5x7 layout with 68g bobagums. The bobagums have been lubed with 205g0. Keycaps are blank PBT DSA. Case is printed with prusament galaxy silver. Comes with a braided TRRS cable. Uses the same PCBs as the dactyl-manuform with holy pandas. If you don't need the keycaps or TRRS cable just subtract $25 or $2.50 respectively from the asking price.
Asking $321
IMG_20210406_190408.jpg
IMG_20210406_190408.jpg (927.42 KiB) Viewed 349 times

-Custom aluminum ergodox (SA Retro not included). Switches are box navy with box royal springs. Going by haata's measurements the royal springs seem to be slightly heavier than jade springs. None of the switches have trouble returning on the upstroke either. Tenting angle is about 20 degrees. Weighs approx 7lbs total. I've shaved down the nubs on the x-axis of the switches, so none of them should be too tight. At worst you may need to use the plastic sheet trick in case some switches are too loose. TRRS cable included.
Asking $210
1.jpg
1.jpg (794.4 KiB) Viewed 13477 times

-Krytox GPL 103/205 mixture. The 103 came from Jocelyn's group buy a while ago and the 205, if I'm not mistaken, is gr2. It's a 1:1 mixture so it started as 1oz total. I've since lubed no more than 200 switches sparingly, so there should still be enough left for several hundred switches.
Asking $4
(or included free with any of the keyboards)
IMG_20190712_175212.jpg
IMG_20190712_175212.jpg (68.49 KiB) Viewed 10817 times
Spoiler:
-76x 67g Zealios (from R4 if I'm not mistaken). These were desoldered from my ergodox so I could put box navies into it. All the pins are in good condition, nothing bent or broken.
Asking $50
SOLD
IMG_20180424_202721.jpg
IMG_20180424_202721.jpg (905.32 KiB) Viewed 14007 times
-80x aristotles in MX housings with switch stickers installed. They're using the stock aristotle spring, so I'm not certain what the weight is. It's similar to MX blue/brown.
-20x MX clears with switch stickers installed
Asking $40 for the aristotles, $7 for the MX clears. $45 if bought together.
SOLD
IMG_20180325_155003.jpg
IMG_20180325_155003.jpg (1.23 MiB) Viewed 14223 times
-110x MOD-H tactile switches
Asking $64
SOLD
MOD-H.jpg
MOD-H.jpg (1.09 MiB) Viewed 12802 times
-Dactyl-Manuform modified to adhere more closely to the ergodox layout. Case is printed with PETG, bottom plates were printed later out of PLA. Switches are box royals with box navy springs. The springs have some lube to get rid of ping. All the switches have the x-axis nubs shaved down, so none of the switches should be too tight. At worst you may need to use the plastic sheet trick in case some switches are too loose. TRRS/USBcables not included.
Asking $200 OBO
SOLD
IMG_20181107_161311.jpg
IMG_20181107_161311.jpg (1.22 MiB) Viewed 12709 times
-120x Zealencios. Put them on my ergodox once, but decided I actually preferred the board sound/feel without them.
Asking $40 OBO
SOLD
IMG_20180418_232215.jpg
IMG_20180418_232215.jpg (867 KiB) Viewed 14137 times
-74x zeal v2 67g with novelkeys cream stems in them. So these are essentially tealios with a different colored stem. I also have the 70g springs from creams if you would prefer those in them instead. They're quite smooth, enough so that I have a hard time telling whether these or stock creams are smoother. The 67g springs are noticeably pingy though. I can lube them for a little extra per switch.
Asking $55.50 ($0.75/pc)
SOLD
IMG_20191119_192118.jpg
IMG_20191119_192118.jpg (890.78 KiB) Viewed 8385 times
-Dactyl-Manuform, 5x7 layout with (retooled) box navies. Case is printed with grey PETG. Switches are hand-wired directly to the pins and hot-glued in place. Case has been modified on the thumb cluster so that keycaps don't hit it. Bottom plate has 20mm circular feet. Dev/tty keycaps not included. Can include PBT DSA grey/black keycap set for $25 extra.
Asking $200
SOLD
IMG_20191230_173818.jpg
IMG_20191230_173818.jpg (1.07 MiB) Viewed 7265 times
-Dactyl-Manuform, 5x7 layout with holy pandas lubed with 3203. Case is printed with dark grey PLA. The case design has a few modifications compared to the other two; different thumb cluster allowing clearance for all keys, different pro-micro/trrs holder as well. The switches are wired up using Amoeba PCBs (pic of the board before final soldering). Can include PBT DSA grey/black keycap set for $25 extra.
Asking $300
SOLD
IMG_20191230_173848.jpg
IMG_20191230_173848.jpg (975.73 KiB) Viewed 7265 times
-Dactyl-Manuform, 5x7 layout with 78g V2 zilents lubed with krytox 103/205. Case is printed with grey PETG. Switches are hand-wired directly to the pins and hot-glued in place. Case has been modified in a few places so keycaps don't rub against it (on both thumb clusters and around the -/_ key on the right half). Bottom plate has large rubber pads for a bit of extra sound absorption.
Asking $250
SOLD
IMG_20191230_173750.jpg
IMG_20191230_173750.jpg (1.26 MiB) Viewed 7265 times
-Dactyl-Manuform case, 5x7 layout printed from translucent sea green PETG filament. Pics don't really do the color justice, it's a nice translucent teal in person. Included would be the hardware needed to build the board: heat-set inserts for the case, bottom plates, screws, trrs breakout boards, and pro-micros. I can include 74x amoeba PCBs and diodes for an extra $13 if you wish to wire the board up using those. I can include a braided trrs cable for $2.50 or a micro-usb cable for $4. If you'd like a finished build with this case feel free to message me.
Asking $60
SOLD
IMG_20200401_164215.jpg
IMG_20200401_164215.jpg (1.47 MiB) Viewed 6231 times
-MT3 dev/tty1 keycaps. Specifically the base kit, ergodox kit, and ortho kit. The only keys that saw any use are the ones shown on the dactyl-manuform below. The other keys are all unused.
Asking $100
SOLD
IMG_20200506_171658.jpg
IMG_20200506_171658.jpg (977.49 KiB) Viewed 5596 times
IMG_20200506_171718.jpg
IMG_20200506_171718.jpg (1.04 MiB) Viewed 5596 times
IMG_20200506_171807.jpg
IMG_20200506_171807.jpg (943.92 KiB) Viewed 5596 times
-Dactyl-Manuform, 5x7 layout with NK creams lubed with krytox 205g0. Case is printed with blue-grey PLA. Some more build pics here. Switches are wired up using amoeba PCBs. The pro-micro & trrs jack use a separate holder I designed. Does mean that right angle trrs cables probably won't fit since the jack is recessed a bit. Bottom plates have a layer of sorbothane on it to absorb sound and give the board a bit of extra weight. I can include a braided trrs cable for $2.50 or a micro-usb cable for $4. MT3 Godspeed keycaps not included.
Asking $290
SOLD
IMG_20200224_180732.jpg
IMG_20200224_180732.jpg (907.79 KiB) Viewed 6603 times
-Dactyl-Manuform, 5x7 layout with crystal jades (springs are lubed to reduce ping). Case is printed in military green PLA. Here's an internal shot. Switches are wired up using amoeba PCBs. The pro-micro & trrs jack use a separate holder I designed. Does mean that right angle trrs cables probably won't fit since the jack is recessed a bit. I can include a braided trrs cable for $2.50 or a micro-usb cable for $4.
MT3 dev/tty not included.
Asking $245
SOLD
IMG_20200503_182043.jpg
IMG_20200503_182043.jpg (812.26 KiB) Viewed 5744 times
-Dactyl-manuform, 5x7 layout with crystal jades (springs are lubed to reduce ping). The thumb cluster is one I designed. The goal was to use all the same keys as the default thumb cluster but only requiring the thumb to move one position left or right to hit everything. Case is printed from prusament pearl mouse. Switches are wired up using amoeba PCBs. The pro-micro & trrs jack use a newer separate holder. The trrs jack is brought up to the back of the case so right angle trrs cables will work just fine. I can include a braided trrs cable for $2.50.
Asking $245
SOLD
IMG_20200812_163406.jpg
IMG_20200812_163406.jpg (1.14 MiB) Viewed 3859 times
-Dactyl manuform, 5x7 layout with T1s lubed with tribosys 3203 & filmed with TX films. Keycaps are blank PBT DSA. Switches are wired up using amoeba PCBs. Case is printed with prusament gentleman's grey filament. Doesn't really show in this pic but at certain angles the filament has this very nice green sheen to it. Under most conditions it looks like a dark blue-ish grey. Most of the parts (save for the right hand case) were printed using my old printer, so the print quality isn't quite as nice as it is with the prusa. So to compensate I'll eat the paypal fees. I can include a braided trrs cable for $2.50. If you don't want the keycaps just subtract $28 from the asking price.
Asking $298
SOLD
IMG_20200825_185025.jpg
IMG_20200825_185025.jpg (832.09 KiB) Viewed 3249 times
-Dactyl-manuform, 5x7 layout with drop holy pandas lubed with tribosys 3203. Keycaps are blank PBT DSA. Switches are wired up using amoeba PCBs. Some switches weren't 100% secure in the case so hot glue was used to ensure they don't wobble. Case is printed with prusament galaxy black PETG. Comes with a braided trrs cable. Here are some other angles. If you don't need the keycaps just subtract $28 from the asking price, if you don't need the trrs cable then subtract $2.50.
Asking $348
SOLD
IMG_20200903_154021.jpg
IMG_20200903_154021.jpg (830.02 KiB) Viewed 3114 times
-Krytox 205g0. I've lubed about 150 switches very lightly, so there's still likely more than 4mL left in this tub.
Asking $9
SOLD
IMG_20200921_174054.jpg
IMG_20200921_174054.jpg (533.89 KiB) Viewed 2884 times
-24x box navy switches. These are pre-retool navies so they have the thick x-axis. Easily solved if you have a tool like a cruciformer to shave the stem down, that or a small chisel will also work.
Free, just pay for shipping.
SOLD
IMG_20200921_174116.jpg
IMG_20200921_174116.jpg (779.81 KiB) Viewed 2884 times

-80x box navy switches. These switches (along with most of the crystal jades) all have a weaker tactility than they should. After comparing with the sprit clickbars, these more closely resemble the 20g clickbars in feel than the 30g clickbars they should. So these are essentially 'medium' clickbar switches.
Asking $25
SOLD
IMG_20200921_173615.jpg
IMG_20200921_173615.jpg (823.33 KiB) Viewed 2884 times
-86x crystal jade switches. The vast majority of these switches have a weaker clickbar as described for the navies. They more closely resemble 20g clickbars rather than the 30g they should. There are a few that are a bit more tactile, but still not quite the normal level of tactility for thick clickbar switches. So these are essentially 'medium' clickbar switches.
Asking $36
SOLD
IMG_20200921_230618.jpg
IMG_20200921_230618.jpg (613.78 KiB) Viewed 2876 times
-100x Kailh box springs. These are rated for 55g actuation/70g bottom out.
Asking $10
SOLD
IMG_20200921_173647.jpg
IMG_20200921_173647.jpg (837.65 KiB) Viewed 2884 times
-Sprit clickbars of all weights. Each of them has approx. 40x clickbars, give or take.
Asking $6
SOLD
IMG_20200921_230340.jpg
IMG_20200921_230340.jpg (857.35 KiB) Viewed 2876 times
--Dactyl-Manuform, 5x7 layout with tangerines. The tangerines have been filmed with 0.15mm clear TX films, lubed with 205g0 and the stems have been swapped with invyr v1 UHMWPE stems. They are incredibly smooth, and there's no 'stick-slip' that I can detect with any of the switches. I can throw in the extra v1 invyr stems I have for free if so desired. Here is a nude shot and here is an internal shot. Case is printed with prusament galaxy silver filament. Comes with a braided TRRS cable and blank grey/black PBT DSA keycaps. If you don't need the keycaps or TRRS cable just subtract $25 or $2.50 from the asking price respectively.
Asking $333
SOLD
IMG_20210201_180344.jpg
IMG_20210201_180344.jpg (900.19 KiB) Viewed 1555 times
-Dactyl-Manuform, 5x7 layout with 68g boba U4Ts. Here's a nude shot. These U4Ts use a linear base rather than a tactile one, so the switches have more of a medium tactility. They've been lubed with tribosys 3203. Keycaps are blank PBT DSA. Case is printed with prusament galaxy black PETG. Uses the same PCBs as my other dactyls. Comes with a braided TRRS cable. If you don't need the keycaps or TRRS cable just subtract $25 or $2.50 respectively from the asking price.
Asking $314
SOLD
IMG_20210408_195119.jpg
IMG_20210408_195119.jpg (923.32 KiB) Viewed 294 times
-Ploopy trackball. Running QMK firmware. Used for a few weeks to get used to it but trackballs just ain't for me. The ball bearing rollers are quite smooth now after breaking in. Red buttons & base were printed by myself. Includes USB cable and a few extra printed parts.
Asking $125
SOLD
IMG_20210120_170013.jpg
IMG_20210120_170013.jpg (442.5 KiB) Viewed 1693 times
Last edited by Loligagger on 23 Apr 2021, 00:01, edited 102 times in total.

User avatar
justcallmecrash

24 Apr 2018, 20:20

Oh, MAN! I really like that ErgoDox. I am in the process of re-building my back-yard aluminum forge so I can cast a uni-body ErgoDox case. I agree that 20% is pretty much the sweet spot for tenting, btw. I'll see if I can find my CAD files from where I had the mould 3d-printed.

codemonkeymike

24 Apr 2018, 20:33

Did someone say aluminum ergodox body!?

User avatar
justcallmecrash

24 Apr 2018, 20:34

Couldn't find the renders, but here's the real deal.
In case you don't notice the comment under the photo - the blue and black one nearest the camera is the 3d printed mould, the one in the background is made of wood (and bondo).
Attachments
3d Printed Mould (for casting) and my original wooden enclosure
3d Printed Mould (for casting) and my original wooden enclosure
ErgoDoxen1.jpg (262.04 KiB) Viewed 14062 times

User avatar
Loligagger

25 Apr 2018, 03:07

Decided to keep the ergodox, consequently put up the 67g zealios which were in it up for sale. However if anyone wants I can build another ergodox like mine for them.

User avatar
Loligagger

09 May 2018, 21:05

Sold the MOD-M switches.

User avatar
Loligagger

05 Jun 2018, 20:36

bump

User avatar
Loligagger

12 Jun 2018, 00:30

Price drop.

User avatar
Loligagger

16 Jun 2018, 02:23

Put the ergodox back up for sale.

User avatar
Loligagger

25 Jul 2018, 19:36

bump

User avatar
Loligagger

09 Aug 2018, 01:06

bump

Drecandlere

09 Aug 2018, 10:10

Interesting point

User avatar
Muirium
µ

09 Aug 2018, 11:20

Any of these switches PCB mount? Do they have two plastic pins in addition to the two metal ones? Especially the silenced linears?

User avatar
Loligagger

09 Aug 2018, 11:35

All the loose switches are PCB mount, yes (I don't have any silenced linears though).

User avatar
Loligagger

19 Aug 2018, 20:05

Price drop on a few items.

User avatar
Loligagger

07 Sep 2018, 19:47

Added an asking price to the ergodox.

User avatar
Loligagger

16 Oct 2018, 22:07

Aristotles & MX clears sold.

User avatar
Loligagger

18 Oct 2018, 05:24

Tactile MOD-Hs have been sold.

User avatar
Loligagger

05 Dec 2018, 00:06

Added dactyl-manuform for sale.

User avatar
Loligagger

12 Dec 2018, 21:11

Lowered the price on the dactyl-manuform.

User avatar
Loligagger

01 Jan 2019, 20:36

Dactyl-manuform sold.

User avatar
Loligagger

21 Jan 2019, 07:17

bump

User avatar
Loligagger

30 Jan 2019, 23:08

Lowered price on the ergodox.

User avatar
Loligagger

19 Mar 2019, 19:59

bump

User avatar
Loligagger

27 Apr 2019, 01:33

Lowered prices.

User avatar
Loligagger

01 Jun 2019, 05:42

Zealencios sold.

User avatar
Loligagger

02 Jul 2019, 22:40

bump

User avatar
Loligagger

02 Aug 2019, 20:06

Added krytox for sale.

User avatar
Loligagger

05 Oct 2019, 20:04

bump

User avatar
Loligagger

05 Nov 2019, 21:12

bump

Post Reply

Return to “For sale”