Custom Cherry MX plate measurements.

Working on learning..... My first keyboard project....

My question is the sizing of the Cherry MX hole to be cut.

Looking through the forum and on the web, I have noticed two different size holes being used. Though i do not know if the difference is enough to cause an issue. There was a comment or two regarding loose switches that had a tendency to pop out or wobble.

I would like to have a snug fit that will hold the key in place and not be wobbly with a good firm snap in. The measurements posted have been 14mm W x L for an H cut pattern and 13.8507mm.

Can the smaller dimension of 13.8507 be used or would this be too small and cause problems? Or is it too insignificant a difference?

If you used a different dimension than the two listed above, what did you use and where you happy with the result?

Thank you in advance.
Attachments
measurements of hole.jpg
lled3733
User avatar

Unread post14 Nov 2018, 10:39

User avatar
X
lled3733
 
Posts: 19
Joined: 02 Apr 2017, 23:12
Location: Switzerland
Main keyboard: Generic mechanical
Main mouse: Logitech
Favorite switch: Blue
DT Pro Member: -
 
Minus 0.15mm for mounting hole is waaaaaay to much.
You won't be able to fit MX-compat switch into 13.85mm
Else you will get switch at least deformed and not able to function properly, stem will stuck.
I have faced this when I was trying to cut 14x14mm holes manually.
Also I was ordering mounting plate cut for ALPS-type switches (size is 15.5x12.8mm) and was trying to use some china clone switches (which for some weird china cheap reason ;) are about 15.52x12.82mm +/-0.01) - while physically putting switch into hole looks like its juuuuust about to fit, but I couldn't do it w/o breaking/deforming switch.
What I wanted to say with this exmaple - hole should be 14x14mm exact, OR maaaaaybe with big approximation it can be from 13.95x13.95mm to 14.05x14.05mm as standards says so.
Also, for the begining you don't really need complex holes, just squares will be pretty much suitable.
q11q11

Unread post15 Nov 2018, 13:59

X
q11q11
 
Posts: 28
Joined: 05 Jun 2017, 12:41
Location: --
DT Pro Member: -
 
Thank you q11q11. I really appreciate the input as you have eleviated the questions and concerns.
lled3733
User avatar

Unread post15 Nov 2018, 14:20

User avatar
X
lled3733
 
Posts: 19
Joined: 02 Apr 2017, 23:12
Location: Switzerland
Main keyboard: Generic mechanical
Main mouse: Logitech
Favorite switch: Blue
DT Pro Member: -
 
As per official Cherry specification distance is 19.05mm and switch hole 14mm.

You often see slightly different values on the forums, they are caused by conversion between mm and inches. Use the diagram below as a reference

Image

More at https://matt3o.com/anatomy-of-a-keyboard/
matt3o
User avatar
-[°_°]-

Unread post15 Nov 2018, 14:48

User avatar
X
matt3o
-[°_°]-
 
Posts: 8654
Joined: 03 Sep 2012, 15:14
Location: Italy
Main keyboard: WhiteFox
Main mouse: Anywhere MX
Favorite switch: Anything, really
DT Pro Member: 0030
 
 
This signature intentionally left blank...
According to this doc https://cdn.sparkfun.com/datasheets/Com...Series.pdf
square mounting hole should have side equal to 0.551in +/-0.002in,
which (by google convertion) is 13.9954mm +/-0.0508mm.

Also I have seen information (on some wiki, but can't find right away) about 0.05mm as non-accumulatung tolerance,
not an addition to distance for every key.
Means that distance between centers of two keys should be 19mm +/-0.05mm.
And sum of distances between centers of 11 keys should be 190mm +/-0.05mm, not 190.5mm.
q11q11

Unread post15 Nov 2018, 19:30

X
q11q11
 
Posts: 28
Joined: 05 Jun 2017, 12:41
Location: --
DT Pro Member: -
 
Thank you matt3o and q11q11. I am reading it all. Feels like I am making progress. Easier to work hard at the idea as I tend to get luckier the harder I research. Besides I really want the first project to work. Again thank you both for the input.
lled3733
User avatar

Unread post15 Nov 2018, 20:18

User avatar
X
lled3733
 
Posts: 19
Joined: 02 Apr 2017, 23:12
Location: Switzerland
Main keyboard: Generic mechanical
Main mouse: Logitech
Favorite switch: Blue
DT Pro Member: -
 
No, key spacing is in Imperial but Cherry MX mounting hole size is in metric.

Standard key spacing is defined as 3/4 of an inch, and an inch is 25.4 mm. That translates to 19.05 mm. The decimal part is not a tolerance but part of the number.
The Wiki article on "Unit" quotes an old ISO standard for typewriters from 1967 which defines spacing as 19 ± 1 mm. Typewriter keyboards of 1967 were not as wide as computer keyboards can be are today. For a "full-size" PC keyboard of today which is 22—23 units wide, the difference adds up to 1.1­—1.15 mm in total width.

Cherry has published different data sheets. In data sheets for the European market, the MX switch's plate hole is indeed defined as precisely 14 ± 0.05 mm square, with a corner radius of 0.3 mm max.
In data sheets for the US market, they have used measurements converted to Imperial.
Findecanor

Unread post15 Nov 2018, 22:39

X
Findecanor
 
Posts: 3053
Joined: 01 Mar 2011, 20:43
Location: Stockholm, Sweden
Main keyboard: Changes from day to day
Main mouse: Wowpen Joy (modified)
Favorite switch: I have yet to find it...
DT Pro Member: 0011
 
Thank you Findecanor. Appreciate the information. Wish this were not my first one ha. Looking forward to finalizing things prior to buying.
lled3733
User avatar

Unread post16 Nov 2018, 04:55

User avatar
X
lled3733
 
Posts: 19
Joined: 02 Apr 2017, 23:12
Location: Switzerland
Main keyboard: Generic mechanical
Main mouse: Logitech
Favorite switch: Blue
DT Pro Member: -
 
Btw I should of asked above. What is the purpose the the H pattern cutout vs square. I have heard conflicting stories. Would anyone be able to elaborate? Does it assist w removing of the switch tops once soldered and mounted as I have read? Perhaps something different?
lled3733
User avatar

Unread post16 Nov 2018, 04:58

User avatar
X
lled3733
 
Posts: 19
Joined: 02 Apr 2017, 23:12
Location: Switzerland
Main keyboard: Generic mechanical
Main mouse: Logitech
Favorite switch: Blue
DT Pro Member: -
 
lled3733 wrote:Btw I should of asked above. What is the purpose the the H pattern cutout vs square. I have heard conflicting stories. Would anyone be able to elaborate? Does it assist w removing of the switch tops once soldered and mounted as I have read? Perhaps something different?

Switch top removal is the reason for the extra cut outs.
Lanrefni

Unread post16 Nov 2018, 05:07

X
Lanrefni
 
Posts: 32
Joined: 13 May 2018, 01:19
Location: Vermont
Main keyboard: Eagletech KG010
Main mouse: Logitech G502
Favorite switch: MX Blues
DT Pro Member: -
 
Yes, Cherry MX top and bottom housings snap together with four snaps. Each snap is next to one of the cutouts in the H-shape, allowing the snaps to flex outwards so that the switch can be opened with the bottom still soldered in the keyboard.
Most clones of Cherry MX have snaps patterned on Cherry's but a few clones don't: notably Kailh and Outemu.

I think the first keyboard that had this shape could have been the Phantom TKL. Its PCB also had four holes around each switch's footprint for a tool, but those holes were shown to be unnecessary. :P

There are a few variations of these switch cutout shapes. One shape is a combination of Cherry MX's 14×14 square hole and Alps' 15.5×12.8 mm rectangular hole for keyboards that support both types of switches. Another allows a Cherry MX switch to be mounted also sideways (looks like a # sign). Yet another shape is more close to an H, for when a plate is machined and your minimum corner radius is larger than 0.3 mm.

BTW. While we are talking about plates: There are three types of stabilisers for Cherry MX, each with different holes. Cherry-style plate-mounted, Costar-style plate-mounted and Cherry PCB-mounted.
There are plate cutout shapes that support either Cherry MX plate-mounted or Costar-style, ... and then there is also a shape (invented by a hobbyist) that combines the two to support your choice of either.
Then there are plate shapes that have quite large rectangular holes for the stabilisers: intended for PCB-mounted stabilisers even though a plate is present. (Otherwise, PCB-mounted stabilisers are for keyboards that have a PCB but no plate). You might find all four variants in various CAD libraries out there.
Last edited by Findecanor on 16 Nov 2018, 07:38, edited 1 time in total.
Findecanor

Unread post16 Nov 2018, 06:07

X
Findecanor
 
Posts: 3053
Joined: 01 Mar 2011, 20:43
Location: Stockholm, Sweden
Main keyboard: Changes from day to day
Main mouse: Wowpen Joy (modified)
Favorite switch: I have yet to find it...
DT Pro Member: 0011
 
Reference (official)
Attachments
Keymodule_MX_EN.pdf
(579.42 KiB) Downloaded 12 times
matt3o
User avatar
-[°_°]-

Unread post16 Nov 2018, 06:50

User avatar
X
matt3o
-[°_°]-
 
Posts: 8654
Joined: 03 Sep 2012, 15:14
Location: Italy
Main keyboard: WhiteFox
Main mouse: Anywhere MX
Favorite switch: Anything, really
DT Pro Member: 0030
 
Thank you all. ''Tis is a drawing from the place I am looking to have the plate made. I will Chang the size from 13.8xxx to the 14mm plus minus .005. My question is regarding the H hole patter. Can I use the measurements indicated in the drawing below in regards to the H step. I have not been able to find the exact drawing but this why I have gathered. I looked at the spec but again I do not find the step size needed. I may just be missing. When I het home I will have some switches to get the measurements from. Again the 13.8056 for the top and side will be adjusted to 14.00 mm.
Attachments
Catch.jpg
lled3733
User avatar

Unread post16 Nov 2018, 09:15

User avatar
X
lled3733
 
Posts: 19
Joined: 02 Apr 2017, 23:12
Location: Switzerland
Main keyboard: Generic mechanical
Main mouse: Logitech
Favorite switch: Blue
DT Pro Member: -
 
I would like to have a snug fit that will hold the key in place and not be wobbly with a good firm snap in. The measurements posted have been 14mm W x L for an H cut pattern and 13.8507mm.

One reason for this might be if someone was making a design for lasercut acrylic plates. The laser has a certain kerf width (basically the amount of material the laser takes away), so you have to account for this in the design. Some manufacturers do this automatically, some don't.
FSund
User avatar

Unread post23 Nov 2018, 13:09

User avatar
X
FSund
 
Posts: 45
Joined: 01 May 2012, 15:51
Location:
Main keyboard: ISO Novatouch w/Norbauer alu case
Main mouse: Logitech G700
DT Pro Member: -
 
Easiest to use KLE, then export that to swills plate tool to create the DXF, then open in an editor to confirm / clean up / modify if needed.
0100010
User avatar

Unread post01 Dec 2018, 05:01

User avatar
X
0100010
 
Posts: 311
Joined: 10 Jul 2013, 22:11
Location: DFW TX, US
Main keyboard: IBM 4707 107
Main mouse: Trackman FX
Favorite switch: Buckling Spring
DT Pro Member: -
 

Who is online

Users browsing this forum: lyktstolpe, pr0ximity, Shifty, tatsurou and 62 guests